Posts

Chosen Solution my TV screen goes black and the sound is still on, I can still hear sound through cable, how do I fix it. Thanks @kphat verify that you have no image on all inputs. If it remains dark, unplug it and push the power button for about one minute, then plug it back in. See if that resets your TV. If it remains dark, use a flashlight and angle it against the screen with the TV at a station where you can hear the sound See if you can make out shadows or shapes....

Chosen Solution SD card reader does not work, and tried both with OS windows and linux. Since it doesn’t work in Linux, the problem is likely caused by the motherboard. Depending on if the chipset or reader is damaged, you may be better off writing the internal reader off and using an external one. On the other hand if it’s simple you may be able to recover the internal reader and use it again....

Chosen Solution I used a plastic dental floss pick similar to http://1stfamilydental.com/wp-content/up… and it broke inside the pin hole. Now I cannot eject the sim try. Is there a way to remove the the piece of plastic in the pin hole without damaging the device? Did you find a solution to this? I have a very similar problem. i went to a phone repair shop. it took them 5min to fix it....

Chosen Solution Hello I repair iPhones and so when my nephew asked me if I could repair his iPod touch I didn’t think it would e a big problem until when I was attempting to remove the digitized I broke some of the copper teeth where the digitizer connect to the logic board. Does anyone know where I can buy a replacement or a place I can send it to get resoldered?...

Chosen Solution The camera lens cover of my phone got cracked. here is the solution for that. https://www.youtube.com/watch?v=4ajI-xJG…. The camera lens cover of Samsung Galaxy J5 (2016) is planted on the back frame.

Chosen Solution miata will not start or crank only humming sound lights do not dim have a new battery tom, right now It does sound like your starter is not working. I would expect the lights to go dim, if your starter was engaging and drawing power from the battery. I suggest that you test the starter according to this:" NOTE: Before testing, ensure battery is fully charged, battery cables and terminals are clean and tight and engine grounds are good....

Chosen Solution Per title, I don’t thinknkts a appliance fault because we have had 3 dishwashers do same.thing The 2nd unit was repaired with a new heating element but broke again after 2 weeks I replaced with a new beko unit and it stopped heating water after 4 weeks. I am wondering if dishwashers are being consistently hooked up to hot water feed and that is breaking the dishwashers overtime? Thoughts?...

Chosen Solution hello all … i have a big problem with 3 devices of access point wa701nd all of them have the same problem no wifi signal , i dont know why !! is there anyway to fix them ?? image for the board : http://s16.postimg.org/jlirbwj85/1265057… thanx Hi, Is the access point turning on when you connect power? What lights are showing on the unit? (p.3 in the user guide explains their meaning) Can you access it by connecting to it via an ethernet cable from a PC?...

Chosen Solution What video cards can I use to upgrade my system mrmac4, your Dell has a PCI Express x16 connector slot which could be used for a video card upgrade. No issues with that at all since a PCI Express graphics card will override the integrated video controller. Dell has annoying proprietary motherboards, but this one still allows small form factor PCI-e GPU’s. If you can explain what you want to use the GPU for, we can select a fitting one for you....

Chosen Solution When I start to pull a shot, everything sounds normal, works normally. Then the pump gets very quiet and stops pushing water through the coffee. To me it seems as if a valve gets shut, but the pump is still trying to pump. If I turn it off, then on again, it works briefly, then gets backed up (or loses pressure?) again. It works fine without the Portafilter in place....

Chosen Solution Can no longer print. Rattled every time but printed for a while but no longer You can try a reset: Turn on the HP device Unplug the power cord to the unit while it is switched on Keep the power cord within reach Press “#” (hash) and “6” (six) at the same time and keep them Plug the power cord back in while pushing the buttons If the message on the display: “Initialization”, “Semi-Full reset” or “Semi-NVM Reset” appears, release the buttons....

Chosen Solution I have had my iMac Pro on a VESA adapter and would like to put it back on it’s original stand. The problem is that the internal connector that holds the stand has retreated into the iMac Pro and I’m not sure how to get the stand back on. Does anyone have any tricks to get the internal “connector” back and locked into a position that I can re-attach the stand?...

Chosen Solution When i am starting up the console a red screen appears is there any solution for this? maarten I would try this first turn off your ps3 with the switch in the back hold the power button down keep holding the power button down and turn the PS3 back on(do this while holding pwr button) switch back on the ps3 If its done correctly, your PS3 should make a loud fan noise causing the fans to enhance for a while....

Chosen Solution I’ve seen similar questions to this, but many of the answers are old (likely due to the age of the device) or don’t address all my questions so I wanted to seek the latest and greatest. My apologies if this is a misstep. I’ve completed the battery replacement of a Surface Pro 2, tested it to make sure everything works, and now need to stick the screen back on....

Chosen Solution Taken apart my ipod as per instructions, all good except cant get the headphone jack ribbon to connect to lift up plastic tab. There doesn’t seem to be any clamp on it to hold the ribbon in place. I don’t think anything broke off on removal, Old ribbon looks the same as new one. Be grateful for any advice on how to secure the ribbon and ensure good contact....

Chosen Solution Replaced the iPhone 11 screen successfully. It is working and responsive however the screen will periodically act as if someone is touching the screen. An example watching something on Netflix and the controls pop up every so often or browsing a website and the screen scrolls to the top as if touching that upper edge. Check that the screen connectors are seated properly. Other than that it is most likely a faulty screen you have purchased....

Chosen Solution Hello, I replaced the upper microphone of my iphone 7 as it was broken and I didn’t hear anything but from the replacement the volume is very low and impossible to understand. Can the part be broken? Can there be other problems? I look forward to your advice regards, Giovanni Paolo You could have a defective part. You could also have a bad connection. I would check the connection for damage and clean the connector with a qtip and alcohol and a soft brush....

Chosen Solution Hi My right headphone has stopped working. It doesn’t play sound but I think it’s some kinde of trouble with the cable because when I bend it right over the remote the sound comes back. Has someone experienced the same problem and have any good advice? the sound in my right earbud won’t work and my music is constantly pausing and skipping when I don’t even touch anything...

Chosen Solution After dropping my phone, it developed the three lines as shown in the attached image. It didn’t have any other issues than this and the screen itself was not cracked. However, whilst opening the phone I accidentally ripped the cable shown in the second image. Is there any point in trying to fix this? I have already ordered a replacement screen but if it turns out I am able to replace the cable and fix the issue of the lines then that would be great....

Chosen Solution Shortly after using my GE microwave/ convection oven the display screen showed all squares and at the bottom of the screen it said to push any button to continue. When I tried to press one of the buttons nothing would happen. Then I tried unplugging the microwave for a few minutes and when I plugged it in again the display showed the same squares. Ten minutes later I checked the display again and it was totally blank and nothing on the microwave worked....