Chosen Solution can you tighten or replace the multi interface shoe mount that’s on top of the Sony a6500? Yes, you need to push the little tabs on the sides up if when you put a flash or accessory on it’s lose. im asking how to tighten the screws that are on top of the camera for the flash. The screws are lose and need to be tighten i just cant figure out how to tighten them as the sides are in the way....
Chosen Solution At least one of the speakers in my Mid 2010 (7,1) MacBook is blown. The amp appears to be fine as sound is clean when using headphones or external speakers. I might as well replace both speakers while I have the laptop open, but I see only a single part number listed. Does the same part work on both or is only one side available? There are two versions of rear speaker (only has one speaker assembly) Late 2009 (side-by-side serial numbers) - 922-9177Late 2009 & Mid 2010 (stacked serial numbers) - 922-9517 Follow this guide to get to it MacBook Unibody Model A1342 AirPort/Bluetooth Board Replacement Update (02/11/2020) Here’s a picture of what I’m referring to looking at the bottom cover
Chosen Solution Hi Folks, It 5.1 Model with a retina, touch bar, and T2. My son replaced the screen in an authorized repair center, which didn’t work initially. Long story short, after visiting apple, they booted the same system with the same screen. ( I don’t remember precisely the issue, but it was something to do with retina verification). The system did work for about four months. However, when the battery ultimately died, it returned to the same issue....
Chosen Solution Customer want’s drive partitioned to be able to boot from 10.13.2 and 10.6.8. I installed a 1TB Seagate FireCuda with the OWC thermal sensor. Prior to installation I had the new drive in an external enclosure hook up to a Mac Pro 2nd generation. Formatted the drive and gave it two partitions. Installed 10.13 and then booted from it and ran updates to 10.13.2. This machine shipped with 10....
Chosen Solution Can we scan the tab through computer or we need to install antivirus in tab? My screen powers on but I can’t touch any thing to pull up keyboard or any thing else. Touch screen don’t work.
Chosen Solution Basically I’m an idiot and I was trying to rearrange my living room and either smushed it moving it or my toddler bumped it big lines down left side. @dleck85 replacement screens are hard to come by. It will of course depend on what model your Vizio is. In general the bigger the TV the less likely you are to find a new panel. Most of the time a new panel, if even available, will cost more than a new TV....
Chosen Solution So when While my girlfriend was using the Kindle it all of a sudden shut off. Pretty sure the battery had some charge, so that leaves me to believe it isn’t the battery. I’m also getting 3.2 Volts off the battery when I multimeter the leads. However, i’m not sure if it’s the screen either. It’s been inside an otter box its whole life. I’m leaning towards the idea that the backlights in the kindle burned out or some other weird screen anomoly but i’d love a second opinion before i buy a new assembly....
Chosen Solution We are a repair shop and we have tried replacing the screens on this model a few times xt1929-17 and every time the digitizer doesn’t respond on the new lcd has anyone experienced this issue or come up with a fix? I am also experiencing this issue! The digitizer stops responding once you turn the phone off and then back on… it’s a little annoying to say the least....
Chosen Solution The ribbon that connects screen to computer from the backside has been cut. Was wondering if I could replace just the ribbon or would the whole lcd need to be replaced. Follow this guide: MacBook Unibody Model A1278 LVDS Display Cable Replacement This can bit of a daunting fix and will take some skill so I wish you good luck :) yes you can replace the cable. and fixit also sell the part : 13" Unibody LVDS Display Cable there is not really a guide to do this but it can be quite strait forward....
Chosen Solution Possible water damage to my s6 edge. The screen no longer responds to touch. It also takes for ever to load after restarting. Sent in to virgin for repair they say it’s water damage and isn’t covered by warranty. Went to phone repair store he opened it up saw some damage on daughter board connecter. Switched out the MB and screen was working. Unfortunately the MB he has is from a demo phone so that won’t work as a replacement....
Chosen Solution Only a small section of my iPad4 screen works (i.e. accepts input). The screen is not cracked. If I understand correctly, there’s the Touch Screen Digitizer and the LCD lies behind it. Is that correct? Which part would I need? Thank you! Somewhat similar post: iPad 4 Broken Screen issue u have a bad digitizer bud sorry u can’t calibrate the screen Cuz its apple and yes u have that correct to Ancer your question
Chosen Solution shutter error message, can’t see through the lens could you elaborate on the problem, you say you cant see through the lens, do you mean through the viewfinder or can not use live view. if you cant see through the viewfinder it is likely that the mirror is locked in the up position and could need to be freed, this would be consistent with the error message you are getting....
Chosen Solution hi i just encountered this site and u guys are doing a fabulous job. i have an issue with my iphone from past 3 months. i did not used it because i dont know how to fix the p[roblem. the problem is that one of the strings in the sim reader is displaced from its actual position. when i insert sim tray the bottom part is broken and was struck in there....
Chosen Solution Hello, I am trying to identify the problem. Is it the LCD or could it be something else? It has never fallen and the “touch” works even on the black side! Thank you Looks like your dropped or banged your iPad so the LCD and logic connections along the edge of the screen got damaged. You’ll need a new LCD panel. Try replacing the lcd data cable It’s cheep and usually 99% of your screen malfunctions....
Chosen Solution I bought an iFixit 5c phone kit, followed the you tube video, replaced the battery; my battery was failing before, would barely hold charge for an hour maybe. After closing everything back up, and setting it to charge, the battery’s power was exhausted after about the same amount of time as my old battery that I’ve had since purchase that was failing. What’s the deal? Hi, It’s possible you could have been supplied a faulty battery....
Chosen Solution Hello I have a iPhone 7 that was in a lake for a month and a half and I was wondering if 91% isopropyl alcohol would work to soak the logic board and other parts in it @apple_fixnoah yes it will. The very first step I would take is to disassemble your phone. Use these guides iPhone 7 Repair to help you disassemble your phone. Take a careful and close look at all components and connectors....
Chosen Solution After replacing the screen some times become black /vertical lines However all cables fixied well What could be the remaining should be replaced? You will have to try another screen. If it’s something else it’s going to cost a whole lot more. Contact the screen reseller if you did the screen yourself because that should be covered under their warranty for defective screens.
Chosen Solution Hi I want to upgrade my AirPort WiFi-Bluetooth to support Bluetooth 4.0 Do you know if i can do this with my Mac mini 2010? Thank you Update (11/24/2014) En français: Oui j’ai posté sur votre site puisque j’ai voulu upgrader ma carte wifi/Bluetooth de mon mac mini A1283 Core2Duo 2,53Mhz pour y mettre la carte du macbook pro 2012 BCM94331PCIEBT4CAX Mais voilà avec 1 peu de bidouillage j’ai pu l’installer et brancher le Ribbon mais je n’ai pas réussi a connecter les 3 atennes J1 J2 J3 donc comme vous me l’avez dit 2 wifi 1 Bluetooth C’est pour cela que je voulais savoir si les câbles d’antennes était les mêmes entre le mini 2009 et 2010 ?...
Chosen Solution I used 50% alcohol on the joystick and now it won’t work at all, i can’t play any games because i have no controller please help me If you did not remove the batteries before cleaning the joystick, then there is a good chance that the liquid conducted electricity and fried the board. You can find instructions to replace the board here. The controller boards are about $15 on eBay....
Chosen Solution Hi, my Redmi 3s backlight is not working. The phone can boot up and i can see the display IF i shine a flashlight on it I disabked automatic brightness and placed it to full but the backlight still doesnt turn on. How and where to test the backlight diode and coil? thanks! I think its around the right corner. Try pressing it. If pressing does the half work for you ie....
