Chosen Solution After putting gas in it wont start the fuel pump was replaced any ideas need to know what im getting into before i buy it Oh no ! you ran outta gas and it sat with an empty tank ! OR, its been sitting since Bush was prez. But first,,, did you see the old pump that was removed ? Was it shiny and clean ? Did the rubber parts appear to be nasty, melted, or rotted ?...
Chosen Solution I recently replaced the battery in my MacBook Pro but it takes way too long to charge for some reason. I returned it and was given another one so that ruled out a faulty battery. I have tried everything from resetting the SMC/NVRAM to restoring the MacBook to factory settings etc but no luck. I’ve also tried different chargers but that didn’t help either! Any help would be greatly appreciated!...
Chosen Solution Hi, I recently purchased a NEC PA322UHD-BK-2, but unfortunately it was damaged during transit (the LCD panel was cracked). I would really like to be able to repair this item, but NEC quoted around $1400-1500 to repair, which is more than I want to spend. I have taken apart the monitor, and have found that it uses a SHARP LQ315D1LG9G panel. I have looked all over the Internet for someone selling this panel, but have had very limited success, either the seller is no longer able to get the panel, or they claim to have the panel, but will only accept Western Union to purchase it (which sends off my scam-dar), or claim to have it, but when I email them back saying I want to buy it, no longer reply....
Chosen Solution Good morning, I am trying to replace the jack of the headphones SONY MDR-ZX 660. The problem is that I don’t really know where I should solder the wires. I have 5 wires on the cable: red, green, golden, light blue and blue+golden (those 2 come from the same orifice). You can see an image attached. I haven’t found any schema on internet which shows the color coding for this combination....
Chosen Solution How do I get into the right drive wheel? The error message is that it’s blocked. My vacuum starts up, moves an inch or so, then shuts off. If there’s something blocking it I need to get inside to clean it out. rabbit3212010 try these things first Error Code C 03 Foreign matter caught in the right Driving wheel. Turn off the emergency switch and remove the foreign matter from the Driving wheel....
Chosen Solution I have a Samsung UN55NU6950 TV, had it for a year now and for some reason on all devices every now and then the audio stutters. It doesn’t happen all the time but when it does, the audio stutters for a second about every minute. It happens on both the TV’s sound and when I plug in my soundbar it happens on that as well? What is going on?...
Chosen Solution Hi, I was scraping off back glass on iphone and scraping tool slid under wireless charger pad and caused a scratch to appear on the back of logic board. The phone no longer turns on could this be the cause or could it be a damaged power flex cable that I also may have scratched, I don’t think it is the latter as if it was the power flex cable the phone should switch on when plugged into a charger?...
Chosen Solution I replaced the glass and digitizer on an ipad mini. Upon removing the LCD it cracked so it was replaced as well. No that everything is reassembled (not glued) the home button and the digitizer aren’t registering. All contact prongs are in place and check out. I’m about to replace it with the only glass/digitizer to double check logic board function but has anybody had this issue before? Installed old/cracked screen/digitizer and everything functions....
Chosen Solution The screen is completely dark and unresponsive. The ringer button on the side still causes the phone to vibrate. Try to restart the phone. To force restart your iPhone XS that’s stuck on black or blank screen, just follow these steps: Press and quickly release the Volume Up button. Then press and quickly release the Volume Down button. Finally, press and hold the Side/Power button until the Apple logo appears....
Chosen Solution I dropped my phone in my bathroom and the screen cracked at the top left and then a large crack also formed across the middle of the screen. The phone seems to function fine but I can no longer use the phone as 90% of the screen is now blank flashing white. Is it worth the cost it would take to repair this or shall I just bite the bullet and buy a new one?...
Chosen Solution Hello, I have a 35in zero-g curved ultrawide gaming monitor v2. My warranty is expired and I’m seeing if i can fix it. When i plug it in the LEDs on the back flash for a moment and then nothing happens. It stopped working after i was rearranging my set up and plugging in stuff. Anyways i was testing the inverter inside to see if it was delivering power....
Chosen Solution My mac book comes on when plugged up but shows red on charger also it just shows the apple with the bar under it and does nothing else can someone help?thanks It sounds like you have two issues here. The bigger one is the fact the OS is not fully loading (Apple logo and the bar). As you didn’t tell us your exact model you could have a corrupted OS install, a bad drive or the drives SATA cable is bad or a combo of these....
Chosen Solution Hello.. I have a Vertical area with no touch response, Like the vertical area containing Character “U” , I can’t type “U” or number"7" I’ve tried to reconnect the Display several times but the problem remains, Any ideas? Thanks … You probably have a defective digitizer. Did the issue come up after a drop, impact or repair? You can find the replacement guide here and the replacement part here....
Chosen Solution Yesterday, I changed the display/digitizer unit because the original screen showed a grey vertical bar on the left display side. I worked accoring ifixit repair guide. After reassembling, the display stays black, only the background lighting comes up. Beside this defect, the phone seems to work properly - it is recognized by itunes and i can flash/synchronize. What I tried: -I tried to reset (home+power) for several times -I tried to reinstall firmware (6....
Chosen Solution You need the standard Airport Extreme Card: http://support.apple.com/kb/HT2256?viewl… Here’s one: [linked product missing or disabled: IF143-001-1]
Chosen Solution I bought new batteries and my instax still don’t work, i’m worried if its beacause of the leakage and corroded battery contacts @suga1234 , Hopa, Yes if battery contacts corroded, they should be cleaned to make a good connection. A pens ink eraser has a little grit in it and works well for cleaning corroded terminals also soft cloth or Qtip dampened with 90%+ Isopropyl Alcohol can work. Have patience clean all terminals, blow/shake any debri out of battery compartment, install new good quality batteries correctly and try....
Chosen Solution I recently found this radio which I dont know when it was made. (date code is 5241), and the FM band does not work. AM works fine but once I turn it to FM all that happens is a low speaker hum. I tried different stereo modes and the oscillation switch but it stays the same. Is there any way to fix this? Hi @rubix_cube , According to this webpage your radio is a boombox from the 1980’s, so most probably it will be an all transistor radio, i....
Chosen Solution HI, I have replaced my lightening connector assembly, and when I’m trying to press the antenna into place it doesn’t seem to “click” into position. It visually looks OK. It is step 35 of the the guide (iPhone 6s Lightning Connector Assembly Replacement). I have tried connecting the antenna from the old lightening assembly to it which doesn’t connect. This leads me to believe it is the logic board is the issue....
Chosen Solution have any idea about easily removing LED from ciruit board, because its too risky to remove like IC leg prints… anu mahe, check on here. It is a very good tutorial and should help you out. You might get a more specific answer, if you post an image on here, about the items you want to desolder. Hope this helps, good luck. You can also purchase a de-soldering pump....
Chosen Solution Is there anyway I can identify which version of digitizer I require, as the new one doesn’t allow touch, without having the original screen to hand? Thanks Hi Jez, When ordering the digitizer, try to match up your specific model number to the part you are ordering. There are times when you can accidentally order a 4g screen for a wi-fi only model and not have it work. I wouldn’t say this is down to revision number on the digitizer itself and the most likely cause is that the part is incorrect for that model itself....
