Chosen Solution i need to find view of complet timing system for a 1999 jimmy 4.3 bobbie, it might help if you give us more information about what exactly you are looking for. Here are the timing chain etc for the 4.3.
Chosen Solution Forgot which order the sparkplug wires go Perry Day firing order for a 3.8engine is 1 4 2 5 3 6 3<—>6 2<—>5 1<—>4 Front of engine for a 4.6 it is 1 3 7 2 6 5 4 8
Chosen Solution I am running 10.4.11. Firewire 400 will not power up or allow computer to recognize my I sight camera or power up firewire external hard drive. the 800 firewire port will not power up the external hard drive nor will the USB 2.0…. Iomega Ego 320gb. Usb 2.0 will power up smaller 80Gb drive I have but its not firewire drive. I have reset psu with battery removal and presing start button while out and off....
Chosen Solution Hello , 2005 Tacoma 4WD light and 4Lo lights blinking when ignition on . 4WD is in op. Plug in snap on scanner to data link port , and everything works fine , lights go out . Unplug scanner and lights flash immedialty Either your front add motor is bad or the 4wd selector switch is blown.
Chosen Solution Folks, I am helping a friend (former student). His Early 2008 Macbook has been running like a dog with 10.6.8 Here’s the specs: I suggested some added memory and bought some from OWC and installed it. The machine boots up and recognizes the memory but once an app or two are open it bogs down and has to be crashed. The pinwheel of death… I PRAM’D it a few times – no joy....
Chosen Solution The display turns off when i turn off the room lights at night and alarm doesn’t go off in the morning. Hi @shikharihani , Have you tried the demonstration mode (see p.22) to make sure that it still functions OK? If still no good, then disconnect the power from the device and press and hold the lamp on/off button for a full 15 seconds and then release it. Reconnect the power to the device and set it up again and check if it now works OK....
Chosen Solution So if I have 2 12s with 600 watt max each running to 1 terminal on a one channel mono block amp. And let’s say I have 500 Watt amp connected ,will 500 Watts go to both subs or will each get 250 Watts? Hi @maxwellh , You have to be careful how you connect them. If you connect them in a parallel configuration to the amp output, you will reduce the resistance (halve) that the amp sees and the current will increase (double - Ohm’s law)....
Chosen Solution Metal tip that plugs in to controller broke off. I have another headset of the exact same model. It’s also broke but the right ear cup bent. Could I wire the cord from on to another? @spencerc22 no reason why you couldn’t do that. Lets see what the damage looks like on both. Ultimately if the cable from the one with the broken cup is good, you can use it as a spare....
Chosen Solution Hello, my friend broke his iPhone 4S digitizer in very unhappy way. He didn’t have backup or synced computers and he had cellular data turn off. I successfully replaced digitizer and turn on the iPhone. Whow! Your iPhone is disabled for 47 years. Okay, so normally after battery replacement iPhone time is flushed and after reboot new time is fetched over NTP via cellular data, synced PC or already signed Wi-Fi....
Chosen Solution My Laptop is actually a HP Spectre 13-ae052nr It’s a super thin x360 / 2 in 1 with a core I7 chip, and now that it’s around 2 years old I’m pretty sure it’s time to refresh the thermal paste. This one doesn’t get so hot, but I know from working on Extremely similar X360 EliteBooks that it’s a bear to pull apart. I’m fearing that I’ll need to pull the motherboard just to re-do the heatsync....
Chosen Solution Hello everybody.I know that in the past was not possible but maybe things changed by now and this could be solved.Do you know if the alert: ‘Important display message’ is it somehow possible to remove ? Or still impossible? yes you have to remove a chip from the flex cable of the original paired screen and solder it onto the new screen. https://www.youtube.com/watch?v=jT6eHy7l…
Chosen Solution Hello, I have a MacBook Pro A1502 EMC 2835. The screen was shattered so I replaced the entire screen upper assembly. When I replaced the screen, I made the mistake of not unplugging the battery connection from the motherboard. Once I was done with the repair. I turned the computer on, the screen was working and it showed the battery dead logo. So I grabbed a charger and plugged it in....
Chosen Solution I am looking for a replacement screen for my 60” smart tv E601i-A3E nichols3 replacement screens , specificly your TV’s size, are not commonly available. If you do find one it will most likely cost more than a new TV. Vizio uses a hodgepodge of LCD screen. To start your search you will have to remove the back of your TV and take a look at the panel itself....
Chosen Solution I just bought a used MacBook Air that happens to be missing the rubber around the display. I bought a replacement gasket, and was able to get it on the top and sides, but wasn’t able to get it in the bottom all the way along the clutch cover. Is there a technique to getting this on correctly, or do I need to remove the display and clutch cover to do so?...
Chosen Solution Okay so it seems only I get the weird electronics. My iPhone 3gs was running smoothly until a couple of months ago. I was running apps and games and whatnots. But while i was reading a pdf file on quickoffice, it decided to restart itself on its own. This repeated for a while. Thinking it might be a software problem, I restored it. Post this, it got to a point where it wouldn’t even charge at all....
Chosen Solution If i fiddle with the right earcup the audio will come in and out. I’m sure a wire came loose. How can I fix it? Exact same problem here. I’m a month of of warranty (but well less than a year of actual use). Right speaker went dead out of nowhere. I’ve never dropped them and took meticulous care of them. I made the mistake of buying SS everything last years (keyboards, mice, headsets, mousepads, accessories, etc)....
Chosen Solution Hi i have s2plus it stuck on Samsung logo And the home button isn’t working How i can fix it ahmad allham there is a whole lot of things going on. The way I would progress is as follows: Replace the battery.Replace the home button flex.For both of the before mentioned things, use something like this video as a guide for the repairs.Perform a hard reset for the phone to see if the “stuck” is a firmware issue....
Chosen Solution Samsung Galaxy S7 owner here. At some point, the original battery got bloated, so I decided to replace it. After the replacement, with the new battery, the phone wouldn’t charge and would turn off after as soon as I removed the charging cable. Charging percentage would show a random constant number (the favourite was between 57 and 60 but could vary). So I took the new battery off and plugged the charger in without a battery attached....
Chosen Solution After I changed the battery the screen became black but there was still signs of life because when i highered and lowered the volume the speakers made a sound @markoo okay so you still have a working tablet just no video. double check all of your work. Make sure that all cables are properly seated and re-connected. If all of that checks out okay then look for and pry damage....
Chosen Solution My screen is flickering and does not show picture. @janestallworth we need a bit more information. If your camera actually still takes pictures but you just cannot see them then you may just have a bad display. This document LCD removal shows you how to replace the LCD.
