Posts

Chosen Solution I followed the instructions on IFIXIT’s site to replace the Pixel 3a’s screen. Everything seemed to work perfectly for a few weeks. Last week, the touch-capability on the screen stopped responding for brief periods. Then it recurred and became more frequent. Now the screen hasn’t responded to touch for almost 24 hours. Alan Fuhs sounds like a bad digitizer which is not uncommon. You want to try another one and then re-evaluate....

Chosen Solution I replaced the HDD drive with an SSD drive..reconnected the 4 cables but not the temperature sensor cable for the new drive. After restarting the system I only get the black screen but the computer is running. Anybody can help me what might be wrong?? First, give the external display a try before you pull things apart. The onboard diagnostic LED’s are located on the bottom left edge of the logic board...

Chosen Solution Hello, The display on my MacBook Pro Late 2016 w/ Touch Bar goes blank after opening the laptop over 1/3 of the way. Any ideas? It almost seems like its a ribbon cable issue on the display side because the screen develops some white spots at the bottom just before it turns off. Yes, your MacBook Pro has a ribbon cable issue between the display & the logic board....

Chosen Solution TV turns on but no menu screen. Tried unplugging it for 10 minutes. Nothing. Tried using a different power source. Nothing. ????? Hi @noneya124 , If you get picture and audio OK when using different inputs e.g. HDMI, RF (coax), Component video etc but there are just no TV menu screens did you try using the TV Settings button to see if you can access the TV menus, rather than just the remote control?...

Chosen Solution Lenovo ideapad 520-15IBK When computer contacts with cold temperature or after start/sleep appear stripes until it warms up. Turning maximum brightness helps remove them faster. Lines appear vertically where is lighter color. They are not visible on the printscreen. I want to know should I replace the screen. Also find a schematics so I can reconnect screen just in case. @internet910 yes that looks like a bad screen/. Could be a cold solder joint or an IC issue....

Chosen Solution So, I bought a 3ds from someone and decided to jailbreak it, turns out the 3ds is jailbroken already and didn’t come with a SD card so i still follow thru and jailbreak it. yet every time I go to the microSD part in system settings it said “an exception occurred” help pelase When devices like the 3DS are jailbroken, it can cause issues with SD reading and game card reading....

Chosen Solution I installed this part and a new battery and after about 17 hours, things were great, however, suddenly my phone doesn’t ready my SIM card. Everything else works, but maybe I did something wrong? Anyone any ideas? Try reseting it to factory settings in iTunes ??

Chosen Solution I was flying my drone and the landing button wasnt working then my drone couldnt land and it ended up wrecking itself to a wall and. Now i turned it on and everything and when i click takeoff button it dosent do a thing not even the motors i dont know wether its the drone or remote please anybody help There is possibly something broken inside or needs corrected....

Chosen Solution Hi guys , my screen is unresponsive, it doesn’t have hardware problem, does software needed to be fixed to fix this screen problem? Ok, it could be a couple of things: Check for the latest software. Sometimes an update that is available may have a patch to the problem, if it’s a known issue and a solution was found.Find out the screen mode, if it’s set to Standard or Zoom....

Chosen Solution Since I replaced my battery, about 3 weeks ago, my iPhone doesn’t show me battery usage stats when I go to settings=>Battery=>Battery Usage, but it only shows me “Battery information will be available after using iPhone for a few minutes”. I made all the software operations to have it fixed, such as battery recalibration, hard reset, reset all the settings, total reset and back up it, reset in DFU mode....

Chosen Solution Laptop is making scratching noises. Scratching sounds are usually from a Hard Drive malfunction. Backup your files and check a guide on how to replace them

Chosen Solution I have a 13" MacBook Pro 2020 MBP 13.3 SPG/8C CPU/8C GPU/8GB/256GB-USA Product #MYD82LL/A The MacBook will no longer charge from the stock USB cable and charging brick. Thinking it might be a bad cable. I tried a different USB-C cable (Thunderbolt 3 Cable 40Gbps Supports 100W) and it worked the first time it was connected and would not work after that. Thinking the power brick might be bad I tried using my Anker PowerPort II 49....

Chosen Solution I have a 2011 MacBook Pro that isn’t showing the WIFI card. It doesn’t show in Safemode or boot disc either. I have tried other WIFI cards, as well as, tried the original card in another MacBook and it worked in that one. So I’m assuming that it’s the logic board connector or something. My question is, where on the logic board should I look for damage? Is there a way to repair this damage?...

Chosen Solution Does anyone have a reliable USA or other source for a q325ua replacement fan? Walmart was the only reputable place I found. I included the links below, but the new ones are temporarily out of stock. You may opt to call their customer service (1-800-925-6278) to find out when they will replenish their inventory. https://www.walmart.com/ip/Asus-Q325UA-Z… https://www.walmart.com/ip/13NB0EN0T0101… Asus-Accessories carries OEM Asus parts, so you can’t get more reliable than that....

Chosen Solution I need to replace a broken xlr imput on my Behringer 212A powered speaker Update (04/10/2017) my speaker is the Berhinger 212A - This control replacement board is for the 212D model. Will the D model board work in the 212A? dmorgandc use this guide for that. You may have to replace the board if you cannot find a replacement connector. The part is available at places like this

Chosen Solution So I’ve adjusted the “Accessibility Features” for the discoloration and the burn in. It took care of the color issues, but I still have old images burned in on the screen. We use this for work, and it will be on the same screen the majority of the time that the screen is on. Should I replace the LCD and digitizer? Or is this a Logic Board replacement? Or something else?...

Chosen Solution I have some TV sets with diverse brands Samsung, LG, Vizio, Insignia, Mitsubishi, Sony etc that I want to rework. They all come with 110VAC60Hz power boards, I want to replace the power boards with 220VAC50Hz, would there be any functional problems doing this? And could I source for the power boards from iFixit? @dadeally that is a very generic question and thus can only get a generic question....

Chosen Solution My thunderbird crashed on me today and when I relaunched it it didn’t display any of my emails in it. I have tried restarting the macbook and relaunched thunderbird to no use. It starts as if starting for first time. Help!!! Look here for help. If this answer is acceptable please remember to return and mark it. I doubt that anything else might be helpful if rebuilding database was not able to bring your emails back....

Chosen Solution The right bumper button, not the trigger - the one above it, is stuck in the pressed position. It doesn’t seem to cause any reaction in the game, so I’m not sure if the contacts are being touched.Bumper doesn’t rebound when pressed, so maybe that mechanism has slipped away or ??? What’s the right way to fix that? Replace the button? Throw this thing I didn’t want my kids to have against the front window of the grandparents that bought it for them?...

Chosen Solution Hi I just bought an X52 pro and when I pull back on the throttle the speed in the game increases and when I push it forward it slows down. Is this a fault with the throttle control or a software problem? You have probably fixed this by now but the problem won’t be the joystick. The joystick sends information to the game as x, y, z values (which the game knows how to read and what axis they come from and then in the game configuration settings, the settings chosen pass the axis values to the function specified, i....