Chosen Solution panasonic TC-50ps14 turns power button on nothing happens red light flashes 6 times Hi, Here’s a link to the section of the service manual that shows what the blink count means. In your case a 6 blink code indicates that there is a problem with one or more of the 4 boards mentioned. Here’s a link that may help to find out which board may be the problem (similar fault condition)
Chosen Solution Where can I find the switch on the transmission to remove it. Thanks. paul1639, until you can tell us exactly what model you have, here is the location on the transmission that was used from 1987-1996. the switch is on the driver side of the transmission, near the front. Number 72 in the diagram. Hope this helps, good luck.
Chosen Solution Scanning and repairing drive C never ends The Boot Sector is probably bad and cannot be fixed. You will be better off with a new HDD. If you get a Western Digital HDD you can download a free Western Digital Version of “western digital acronis true image download” which if you have an external enclosure you might be able to recover at least the Restore Partition of your Original HDD....
Chosen Solution Ok so I replaced my led back lights but when I put back together my led lights turned on and screen was black. Then at bottom mid of screen redish yellow vertical lines start slowly appearing. Tv automatically turns on as soon as I plug it in. I do not believe I damaged the panel. I however unplug the t con board while tv was on and lines go away and theirs a solid black screen with back lights working....
Chosen Solution I replaced my camshaft position sensor on my 2013 terrain and a week later the check engine light came back on with 3 more camshaft errors all the same. I was told that having so many camshaft errors could be symptoms of another problem . Is that true. Update (09/25/2019) Mass of volume airflow circuit malfunction “A” camshaft position-timing over advanced or system (2x) Michelle high absolutely possible. To help you further we would need to know which error codes you do get...
Chosen Solution my samsung smart tv is stuck on the start screen it was working fine last night but won’t get past the samsung logo at the beginning. controller has been unresponsive. any ideas or anyone solved this problem? thanks Update (02/13/2017) would i have to replace the mother board or power board? @drew24 , Andrew, On some models this reset may work, disconnect TV from outlet, press and hold the power button on the TV itself for about 30 seconds....
Chosen Solution Can I change the soleplate Most irons today are throw-a-way. As much as I hate saying that the sole plate is often not removable from the tank and controls. Instead of trying to replace it have you tried carefully lapping out the scratch with some jewelers rouge? First run your fingernail across the area does it catch on a sharp edge? If it does you’ll first need to carefully file the edge down....
Chosen Solution So I cracked my screen and there’s glass missing on the top left corner so you can see the camera lens inside. My phone started to loose signal here and there…. It kept getting worse and worse until the point where I only had signal for about an hour a day. I realized that if I put extreme pressure on the top left corner of the screen, the signal would come back....
Chosen Solution Hi! So my iPhone randomly starts to flicker and becomes unresponsive for a while, Whenever it decides to work again I can use it up to a day before before it reverts back to flickering and the screen unresponsive. I’ve tried turning the screen brightness down and rebooting the phone which people have suggested. What else might fix the problem? Many thanks! Sounds like a faulty screen, did you get the screen replaced by someone before?...
Chosen Solution When opening my phone to replace earpiece, the glass pulled away from the ‘bezel’ or frame that it is mounted in. I can see pieces of glue. The attached bracket (LCD Frame?) remained clipped into the rear case. Once I realized that this was not right (opened to about 20 deg angle), I pushed the glass back into the bezel and worked harder to open the phone “correctly”. My question is: now that the glass is not totally secure in it’s mounting ‘bezel’ what is the correct type of glue to be used to make sure the glass does not pop out in the future....
Chosen Solution Hello everyone and iFixit team I’m making this post so everyone can see the mistake every supplier is doing and making techs not able to solve the front camera recording or talking to Siri after replacing the front camera proximity cable. All the SE front camera proximity sensor everyone has been buying are 5s is not the same! The front camera will work proximity sensor will work and receiver will work but the microphone is different....
Chosen Solution while using camera in water, it stopped taking pics. and showed “door opened” on it, even though battery door was shut, now it doesn’t turn on. How do I know that it may be just the battery that may be damaged? Possibly a faulty seal or door catch. Open and remove all memory cards and batteries. examining closely for any sign of water inside the camera. Cut some thin card (cereal packet type) or paper into a strip....
Chosen Solution will it hurt to put the largest ssd into a mid 2012 macbook air Your system uses an older version of the custom Apple blade SSD, the largest available is 1 TB. Here’s two sources: Trascend - JetDriveOWC - SSD Flash Storage Upgrades MacBook Air 11" & 13" 2012
Chosen Solution My laptop is really slow when gaming and I dont know what to do about it, I have tried a lot of things but nothing works,… It depends on the game. Many entry level to midrange IGP only laptops handle games like The Sims okay since it’s not demanding, but will struggle to run more demanding games that recommend or require a dGPU. In many cases, professional graphics like the Radeon Pro and Quadro series will work but may struggle since these are optimized for certain workloads and are ISV certified....
Chosen Solution (SOLVED - please read info below the original message) Original message Does anyone know how to reset the SMC directly from the MBP 2007 A1226 (820 2101-A, model of the logic board )? Is it more effective than the standard cmd-option r+p? The fans of my MBP blast full speed from the start and have not temperatures available). This could really need a proper reset. Please let me know if there’s a way....
Chosen Solution Hello, It is possible to change/upgrade the memory for a 32 or 64 gb on a 16gb iphone 4s? thanks In order to do this, you would need to desolder the flash memory from your iPhone’s logic board, then solder on a recycled one from an old iPhone with a larger storage capacity. This would require a TON of soldering skill, as you would have to properly desolder the flash memory from both devices, then resolder the larger one back on to your device....
Chosen Solution Hi, I have a early 2011 Macbook pro and two of the battery connectors on the logic board have snapped off. Just wondering does it work without the two ground connectors, if not, is there a way to fix this without replacing the logic board? I would recommend you get the logic board fixed. You could stress things if the pins are missing which could cause a failure. As to fixing the logic board, It depends on what is damaged....
Chosen Solution Okay here’s the issue I’m having with my Kia Dealer. They are quoting a ridiculous amount and time to change the transmission fluid (Nearly $800 and 3 days ) on my Sorento and apparently do it on every Sorento and there’s a waiting list. I find it very odd as to why the vehicle’s entire transmission needs to be taken out and dismantled in order to do a transmission oil change....
Chosen Solution I need to replace the cooling fan in my Acer 4810T laptop. Does anyone have a procedure for this? Leigh, here is the page that has the disassembly guide. Click on the link and download it. It will show you how to disassemble your Acer and will show you where the fan is located and how it is fastened. Hope this helps, good luck.
Chosen Solution Hi, My MBP Mid 2012 was damaged by water. It was pluged in and turned off on my desk, there were rain and the water filtered through the ceiling (it was at night while I was sleeping), in morning my MBP was flooded. I went to an autorised service center, and they told my that the Logic Board is damaged. The part price is $900 plus tax. They don’t asure me that the MBP will work in perfect conditions after replacement, they say is 50-50 change to get more malfunctions with the new Logic Board....
