Posts

Chosen Solution Hi, im desperate at this stage, i have a macbook a1502, i don’t know what else to do? the laptop was working fine, then i closed the lid, opened in 2 days later, nothing. just a green light on the charger. i took it apart, and when i was putting it back together again, it magically came on again on it’s own, i fully tested it, perfect! turned it off and on again, lovely, again, closed the lid, opened it 2 days later, and now im in the same situation again… i have power on all the rails I’ve checked… and green light on the charger… any ideas?...

Chosen Solution Hi! I bought the headset with the whole kit second handed.. I was told I had to change the tether cable wich I did right out of the bat but display still is showing vertical pixels ray.. It moves and changes from image to images.. Not fixed pixels being the problem but seems display or mother board… What should I change or test first? @jfooo the lack of schematics etc....

Chosen Solution I want to find out how to repair a Salt Chlorinator Cell? It’s a seemingly sealed unit with two electrodes inside which convert salt to chlorine. These electrodes get worn out or used up over time. Can these be replaced or replated? Any special tricks and things to know? Anything to be aware of so as not to mess things up? What’s the worst that could happen? Most cells can be replaced every 4-5 years....

Chosen Solution Because the lock is quite new when it happens, it is likely due to an installation issue : alignment issue, friction issue with the door metal face plate, or the screws on the rear body plate is too tight or too loose. This can happen after a recent installation or after the door had a hard slam (due to wind etc.)

Chosen Solution screen backlight won’t turn on after locking or turning it off , I had taken it for repair but it keeps happening after it’s fixed I have this problem also. Would love a fix… I had the same problem… just appeared today. I was able to solve it by changing my screen lock from Pattern to Swipe. I let the screen turn off and then was able to push the center button and it lit back up....

Chosen Solution Does anybody know where to find a replacement screen for a sharp LC-65N6003U @ethanbus screen that size are in general not available for purchase. The cost for a single screen will be prohibitive since you will also need to consider shipping etc. We can always check but will need the LCD panel number, not the TV model number. Remove the back from your TV and let us know what the label on the LCD panel says....

Chosen Solution It seems that my iPhone X has got water damage, I can confirm this by looking into the SIM card slot and seeing the red line. The phone has been prone to getting damaged when in contact with water, from being in the rain or tipping water on in; usually the screen will flicker and after leaving it in the sun it works after. Not sure why my phone has had this issue....

Chosen Solution I just finished replacing the screen, but it completely refuses to light up. It’s still responsive to touch because I can unlock it and it makes the lock sound when I lock it. So i know im unlocking it. Same for the original screen. It wont light up, but you can still press buttons (that is if you know where they are) like im able to hit the snooze and end buttons for the alarm, I can unlock it, and I even turned it off like normal so I could even replace the screen in the first place....

Chosen Solution I shattered the glass on my ZTE Blade V8 Pro and cannot repair instructions anywhere on the web, came here looking for some help. Hello, if you are looking for a step by step guide on screen replacement for this phone there isn’t one yet. But if you are a little bit tech savvy. You can look up to ZTE V7 screen replacement. https://www.youtube.com/watch?v=c877YOxB… Here is a quick diagram of the phone broken down....

Chosen Solution Card fell out of tray when putting it into phone and is inside the phone not on the tray how do i get it out? You’d have to open the phone and physically move the sim out through the holes in the sim tray using tweezers or anything with a fine point to avoid bending the pins.

Chosen Solution At machine start up the message ““Error 46 clean impossible” appears. user’s guide says it is a generic mechanical problem, but there’s nothing wrong inside. Could be the printing head to be replaced? I am currently working on this myself. It means your ink absorber pad is full. I purchased a new pad, but now I can’t find instructions on how to install it. Apparently, Brother really wants you to have a technician do this, or buy a new printer....

Chosen Solution Where are the freeze plugs located on 2007 f250 6.0 harley davidson edition and how to replace them OK, by freeze plugs you mean the (welsh plugs in my country) brass or mild steel plugs in the engine block? They are usually on the side of the engine block, this site has pictures and a write up on how it is done. Simple job if you know how. https://www....

Chosen Solution when im trying to restore my iphone 4 the itunes gives me 3194 error, i did delete those lines from the host file but it still the same? what shud i do? You can use tiny umbrella to get your shsh blob save onto your computer and the then use redsnow the latest one to restore it then everything should be find as you mention you edited the host file so i pressumed you know what you are doing....

Chosen Solution I have a 1989 toyota P/U 22R carb …bought for $200. reall good condition for the age …. watched a new water pump and radiator belt be installed. so it over heated. cooling problem I’m observing. trucks sits another 3 days and the person is try to sell it to the wrecking yard. they say it’s blown up. ok I’ll by it for 200. ok deal … so new rad cap new thermostat it was frozen the rad cap was blowing water out the top and water slightly out the tail pipe very hard to start....

Chosen Solution Have a 91 Honda Accord that the radiator fan come on when you first crank the car and it stays on continuous while car is running and after car is off. If anyone has any info on this it would be much appreciated. @adunlap21 check the temperature sensor which acts as a switch to turn the fan on at a certain temperature. It is possible that it has failed and stays closed....

Chosen Solution Hi All, I bought a second hand imac a week ago. It’s an old 2011 imac, with High Sierra installed. I tried to change the username of the user (which was “azerty”…) using the user and profile tools, but when I restarted the mac as requested, I noticed that : the username wasn’t changed. 2) it’s not admin user anymore ! It seems to be a know high sierra bug… So I now have a mac with no admin account… I can’t install software nor create folder/ copy/paste file in the backup disk…....

Chosen Solution So have we decided that the GPS antenna and the WiFi antenna are two separate assemblies? And if so where are the instructions for remove/replace the WiFi? The WiFi antenna connects to the logic board with connector #6. The antenna sheet is at the top of the iPhone. https://d3nevzfk7ii3be.cloudfront.net/ig…

Chosen Solution I have a good monitor with a broken power suply. Anyone know where to get this pcb? In good condition and cheap;-) Thanks in advance! Pauluz de Boskabouter if nothing else you could always try and repair your board. Here is the schematic for it SAMSUNG BN44-00195A Hi, By “print” do you mean “printed circuit board” (pcb)? Here’s a link to a supplier of the board. It is shown only to give an idea of the cost of the part....

Chosen Solution PSP will not work without it charging and even then will randomly shut down and factory reset. Ive changed the battery numerous times and checked the charging output which at first, the charger that came with it was not supplying enough power to charge properly. I got a stronger cable (one that is recommended for the PSP through Sony) still have same issue It can be an issue with the battery connector....

Chosen Solution So i had an idea to put my late 2014 27” iMacs internals such as the motherboard, power supply and all the Necessary components to make my computer function normally into a custom case i will make myself. My iMac has a few cracks in screen and that really bugs me but a new screen costs $500-$600 which is a waste of money and out of my price range....