Posts

Chosen Solution samsung rf31fmesbsr/aa freezer not cooling. Evaporator fan is working, no ice build up. Compressor is running. Temperature stuck at 65 Hi @jtphilly , Is the evaporator unit getting icy cold? Is the compressor running constantly trying to drive down the temperatures? If the answers to the above are no and yes then there may be a problem with the sealed system. A blockage in the sealed system, a lack of refrigerant or a faulty compressor....

Chosen Solution Hello, just out of curiosity. My colleague got its notebook broken (seems something got sort circuited) and it seems it took the Samsung MZ-VLW2560 drive with itself (the drive, connected to external adapter only heats and is not detected). I had quickly used multimeter over the drive and had found out, that chip S2FPS04X01 A1708 604C858 has several pins connected or shorted to ground. I am not able to find datasheet, but I suppose its some kind of drive IC and since its in QFN-36 body, that only thing connected to ground should be the plate underneath the chip, not the side pins....

Chosen Solution Sorry Inhad to put the worng tv couldn’t find my model tv My samsung ru7100 43 inch has a black horizontal line started afther the TV turnd of and on by its self a couple of times what can this be is it fixable? @luismano90 horizontal lines are almost always caused by a failed driver on the LCD driver board. It is part of your panel and schematics. etc....

Chosen Solution My camera fell and there are no screws keeping the screen intact with the camera, so it’s being held with the thin cable, which looks like a film. The film ripped, so now the screen is completely detached from the camera. What do I do??? How much would it cost to get the screen attached back to the camera? Also how much to replace the screws? Aminat, I searched eBay for replacement LCDs for your camera....

Chosen Solution The screen on my V10 turns on without warning or request. When laying on a table, putting it into a holster or pocket. I can turn the screen off but it will turn back on without me doing anything to trigger it. I am very careful not to double tap the screen or touch the power button on the back. I can’t find a way to stop it or make the device less sensitive....

Chosen Solution Dropped phone. turns on see display but won’t respond to touch First, check if your digitizer connector still connect with motherboard or if it got loosen. If replug can’t solve the problem, you may need to replace a new touch screen. Good luck to you! bad connection on logic board. Reseat the connector. The 5s is under a 1 year warranty…still, so take it into apple.

Chosen Solution •Shattered around home button •Screw twists from clockwise to anti clockwise • Left Bottom screw is stuck where the screen has come off •Point two indicating that it is not stripped Hi Screens have 2 anchor point the screws attach to. Sometimes if there is big drop the anchor points break of the screen, resulting in the screws not being able to come out, but are also not attached to the screen....

Chosen Solution I recently did a memory upgrade on this device. After the upgrade was complete I noticed some strange problems that I could not explain. First some of the keys on the integrated keyboard did not work. I did a battery reset and it seemed to correct it but the problem soon returned. Further attempts to reset the battery produced no results. Then I noticed that the computer would no longer operate on battery without the charger....

Chosen Solution not power .problem mainnboard , no sharj and no start and no screen never on mobile How do I get the phone working for data recovery? This is for my former LG G4 509K phone, but the same procedure usually does the trick on LG phones. Way more often then not, the issue on phones like the G3 and G4 is bad solder joints. If you can open the phone and reflow it, this will get it going again for data recovery purposes ONLY....

Chosen Solution my canon 1200d suddenly turn off and is not turning on plz help me Sounds like a battery problem. Have you tried a different one? Yes’, but still its not turning on my camera canon 1200dEos…its not on….even my battery is full i do no how to solve this can anyone say how to solve this problem

Chosen Solution during carpenter operation i used my camera to film any sequences of the job,the air was a little bit contaminated with wood powder and dust. After use i noticed a thin layer of dust and some chips inside lenses that compromize photo quality. Unable to clean. marco, there are really only 2 ways of doing it. One is to completely disassemble your lens and to clean the components. This is very involved, requires soldering and working with very small and intricate placed parts....

Chosen Solution I need some help with possible issues. I replaced the battery in my phone and all works great except now both cameras are blank and not able to take pics. What now or where to go from here ? I have new cams in route but I don’t know what could be the issue. Did you disconnect the screen prior to removing the battery? It’s possible that the front camera flex cable that is attached to the screen became damaged in the process....

Chosen Solution I replaced the screen, battery, and the power switch / LED cable on an old iPhone 6. The screen replacement and the battery went well (with the exception of the touch id button — separate issue); however, the rear facing camera stopped working. Additionally, the LED continues to be non-functional, and shows the “device too hot” warning. Of course, the device is not too hot. The power button (part of the LED cable) does function properly after replacement....

Chosen Solution Ok I went to bed left my phone on charger. Got up turned it on and get this screen that says if I want to download new OS push volume up to continue or volume down to cancel this. I never asked it to do anything of this type period! It refuses to recognize me pushing the volume key down to get out of it and cancel. I have tried factory reset several times no good....

Chosen Solution my qx95 hovers great and then all of a sudden it just yaws to the right usally or sometimes to the left and it doesn’t mater if I have my hands on the sticks or not, I can be just flying in a strait line and all o a sudden it just spins around and comes at me or the other way you can never tell, I have 6 quadcopters and this is the only one that does this and its brand new, any help would be great...

Chosen Solution Hey guys, so i got a battery from iFixit and soon after i replaced it i began to get random shutdowns, the mac was running incredibly slow. I noticed when it started to get really sluggish if i press the button for the battery indicator (the one on the side) it showed like there is no battery (no lights lit green) Had to reset the SMC in order for it to work properly again....

Chosen Solution Hope someone can help. Have this side by side GE Profile Artica PSC23SGRB model: PSC23SG RB refrigerator. Woke up and found it totally not working. The top lights on the frig side were off and the bottom ones were on in the frig side. All lights were on in the freezer side. the upper control indicator would light up. When pushing the freezer control to 0 but it would just snap back to the room temp....

Chosen Solution was watching tv went to change channel with remote–remote wouldn’t work–changed batteries-still not working–call tech support-done everything they said–still not with remote. we have to manually turn on/off/change channel/volumn. does remote need reprograming?? think sensor might not be working?? how do we find this out? this a vizio tv–1 1/2 years old. To check if the remote is working or not or if the batteries need changing, open the camera app on your phone, point the remote sensor at your camera and your camera should pick up the infared....

Chosen Solution I was wondering if you could repair a water damaged IPHONE 6? please let me know, I’ve put it in rice, and its not responding Thanks The logic board is probably damaged by the water. Your best bet would be to get the logic board replaced. You could also sell the other components such as the screen if you’re thinking of upgrading.

Chosen Solution I need to temporary remove the ends from my Dyson handheld vacume metal tube to fit into my suitcase @cyprus , Richard , Check for any plastic caps/collar that could be covering attaching screws or rivets that could be removed to get ends off. I think the ends look to be hot pressed on or epoxied and are not meant to be removed. If you want to chance it, you could try heating up the plastic collars with a heat gun and turning/pulling off(may take great effort) and then epoxy back on if needed(no guarantee)....