Posts

Chosen Solution After dropping my phone without anything screwed in, the battery fell out and along with it, the battery connector was ripped off. No solder pad seems to have been affected. How would I go about fixing this? I’m not too skilled in soldering nor do I have the equipment to do so. @invoxiplaygames the connector will have to be re-soldered (no, you cannot glue this coonector;-). Replacement connectors are widely available on line and since the solder pads still look good, anyone that does small electronic repair could solder this for you....

Chosen Solution Hi, where can I get the foot piece of my Shark vacuum cleaner repaired - model number NV350NZ. I live in Auckland New Zealand. If can’t be repaired where can I buy a replacement? If your Shark Navigator Lift-Away Pro vacuum’s floor roller no longer spins, see the Shark Navigator Lift-Away Pro Floor Roller is Not Spinning problem page for possible causes and solutions.

Chosen Solution One of the rubber feet came off of the bottom of my laptop. Where would I find the exact part to fix this with? Dell Precision m6700 laptop I’m sure a quick google search will help you find what you’re looking for. Regardless of where you buy it from, it’s not going to cause any harm to your device.

Chosen Solution If i put a s4 i9505 charging ribbon to a s4 i9500, it will work? Hi @chkontog There are separate charging ports for every model of Samsung Galaxy S4 due to the different antennas built into the flex cable. The charging ports are interchangeable but you will likely has service issues if you use a cable that doesn’t match the exact model number. Since the cables are so cheap, you should invest in a new replacement part....

Chosen Solution I was playing normally on my pc suddently part of the monitor brightness went off, I could still see that section but less. Hitting or shaking the screen a bit would fix it or sometimes make it worse. Other areas of the screen might have no brightness. I tried opening the monitor, and I notice that the cable to the bottom of the screen from thr main board is VERY loose, not the male connector but in fact the frmale connector....

Chosen Solution About a week ago, i put my samsung galaxy s7 edge in water since it’s water resistant, later i found out that the sim tray was wet so i cleaned it and put it back in. The next day the screen turned all black but the notification light and vibration was working. The screen would come back on when i restart it but would go black again after i locked and unlocked it....

Chosen Solution The iPod fell, it had a crack across the screen it worked fine until the screen went completely black, it stoped giving power to it. Made the screen useless it works i can sync it to my i tunes and what not. @sik24 , David , At the 1st link below, you can select your model and click on the appropriate guide to see how screen is replaced. At the 2nd link you can choose your device to see if replacement part is available through the ifixit store and if not just do a google search for your part....

Chosen Solution Anytime the camera is not being used I close the screen (lcd facing in toward the camera). The issue is when the screen is opened and flipped. The screen no longer rotates when opened, flipped than closed. Anyone have any ideas? Try completing up to step 2, see if there is an issue with the mechanism. Nikon D5200 Screen Replacement

Chosen Solution My phones screen was cracked for a while but it was small and the touch worked fine. This morning I dropped my phone and the drop messed up my graphics and the touch worked 30% of the time. I took my phone somewhere to get the screen fixed and it was expensive.. ANYway I went home and went to take a photo and black! The front and back were black....

Chosen Solution One day my iPhone screen started to get vertical lines. I took the phone apart and replaced the screen, when I replaced it, the new screen had vertical lines. I tried rubbing connectors with alcohol and it didn’t fix the issue. I’m desperate to get into the phone just to hit “Trust” to backup my data to use on my new phone. Are these lines small white bloks? Or like this: Dont Know why has white vertical line on the screen

Chosen Solution Can anyone tell me what is the name/ type is the male connector (i.e the six pin plug) need to try and source some, in order to make extension fly lead to tap into the 3.3v and ground to power a PWM module. The panels LED’s load is far greater than what the SD card reader line was designed to support. Interesting idea for sure! FYI: The GPU does not control the backlight....

Chosen Solution My JBL Flip 4 won’t power on and when I plug the charger in a single red light blinks where it should be charging. This is all it will do however it was previously working. It hasn’t been dropped or anything and just stopped working. If your JBL Flip 4 speaker refuses to turn on, see the JBL Flip 4 Won’t Turn On problem page for possible causes and solutions....

Chosen Solution Нow to disassemble the case and replace the battery? If anybody is still interested in this, I recoded my process of replacing the batteries in a Braun Cruzer3: http://spbnick.github.io/2016/06/24/Brau… Cameron Frye, still trying to find an English version but here is something interesting. http://www.service.braun.com/line/SH/S57… it shows the picture on page 8 how the batteries are changed but in Chinese and was omitted on the English version. Hope it will get you started until we find something in English...

Chosen Solution Have a kindle amazon fire works great but has a busted screen… Have a Rca Tablet great casing but the insides are burnt up… Anyone kno if I can put the busted into the burnt??? No they are both different tablets.

Chosen Solution Does this model come with the 12 hour format instead of the 24 hour. https://docs.sony.com/release/ICFC1.pdf That might be of use. I wouldn’t. America uses 120v whereas the UK uses 230v.

Chosen Solution Running Apple Service Diagnostic (OS version) test suite v.3S162 on a 2014 13" MacBook Pro (3.0GHz version, MGXD2LL/A), it says FAILED on one test: Thermal Interface - Processor:Processor0: Extended TIM Test 75 Percent GB (test #16) - Extended TIM Test 75 Percent GB - Check that CPU is properly attached, using product spec theta dh + 75 percent guardband. [1 minute 24 sec] ERROR – 8 [Plimit not as expected....

Chosen Solution HI ! I have a Mac mini (Mac Mini 5,1 Mid 2011 , 2.3GHz intel Core i5, 4GB RAM)model that has a stock HDD (Toshiba MK5065GSX 500 GB SATA III 5400 RPM).Now the HDD has a SMART issue and I have ordered Seagate’s ST500LM000 (500 GB laptop thin SSHD). The only thing I am worried now is that Toshiba HDD had 9.5mm size while the SSHD has 7mm thickness....

Chosen Solution While I stop on the traffic light the engine stop working, I start it again and it starts knocking very bad, what may happen the engine has only 54k. High speed knocking is usually a blown piston rod inside the engine, which often damages other parts in line like the cylinder block where it needs to be re-honed on a CNC machine (or it will burn oil, even with new piston seals), but the top end often survives where the GDI or lifters are installed unless it’s really bad or run like that for hundreds of hours....

Chosen Solution Serial number D25t206ygq17 EMC 2834 These repairs are not just simple “ow do this” step by step, i have a lot of questions. A- DO i have the right model selected? The computer is dead so i can’t verify what i have exactly. B- Will a standard desktop hard drive work, i have a 3tb i just took out of my DROBO i want to use. Never opened up a modern IMAC before....

Chosen Solution need to know where is the ac relay and ac fuse is located. Here is a link to the manual for your car. Scan down to the bottom of the list to where it says download. Fuses and relays are on page 154. Good luck. Ralph http://www.myacrobatpdf.com/1992/ford-fo… A common cause of the ac clutch not turning on is lack of refrigerant gas in the system. There is a pressure switch which detects that there is enough gas and if not the ac clutch won’t engage....