Chosen Solution I have changed the spark plugs and spark plug wires and the distributor cap and the fuel filter If it backfires when you let off the gas peddle it has air getting into the exhaust, either an exhaust gasket or cracked manifold before the catalytic converter or the emission control’s Air Injection system. The air injection check valves (STANDARD MOTOR PRODUCTS PT#AV7) are common failure parts. Cost about $18....
Chosen Solution Hi all, I was pleased to learn that with my model of Macbook Pro it’s possible to upgrade the hardware and have it running at approx. 0.3hz slower than the basic current Pro. I was also pleased to learn that removing the optical drive will significantly lower the weight. As a novice to modifications of this kind, however, I’m slightly overwhelmed by the options and could really do with some knowledgable input with regards to a few specific questions I have:...
Chosen Solution after change the front camera auto brightness doesn’t work and try another one also doesn’t work thanks The Front Camera flex also contains the proximity sensor. You may have installed it incorrectly as it must be properly lined up within the screen frame. Ina worst case scenario, the sensor may also have been damaged. Take a look at this guide to insure the flex is properly installed.
Chosen Solution the belt pulley is rubbing on the cover,what would couse this? than you @markb012 could be loose pulley that rides f the shaft or a bend cover as well as a bad shaft bearing. We would need to know what exact model it is and if you can post some images of the pulley etc. That way we can see what you see. use this guide Adding images to an existing question for that....
Chosen Solution Good day to you all, my fellow hardware repair enthusiasts. I have stumbled upon a very annoying issue with my notebook and I am wondering if somebody could provide me with much needed help. Yesterday my GL702VM started to hibernate randomly without any apparent reasons. Before hibernation a default Windows “Locking” screen with a progress indicator spinner appears for half a second. After that it won’t start properly and it will turn off immediately after turning on (it turns on, I can hear the HDD and fans starting to spin and then it immediately turns off, the whole process takes less then a second)....
Chosen Solution We have a Maytag MBF2255KEW with the bottom drawer freezer. Both suddenly stopped cooling yesterday, uneventfully (just went to grab milk and it didn’t feel as cold as usual.) It sounds like the fans are running constantly. We cleaned the coils underneath the fridge last night but still isn’t cooling this morning. Any ideas of what it could be? Update (04/19/2022) @jayeff we did come across this when we took the freezer panel off....
Chosen Solution Hi So my remote stopped working. Tried new batteries obvs, tried the camera check and I can see the ir working. So I’ve taken the tv apart after looking online for a fix. I’ve got the ir board V28A001326A1 out. Trying to buy a replacement but had no joy. Does anyone know where an which ir sensor is fitted to this board, and where I could get one? I can solder so that’s not a problem....
Chosen Solution I had a repair done on my laptop and they cut the wires to the WiFi antenna. Do you have instructions on how to replace the antenna? I would not trust them with my laptop again. Sorry to hear you had a bad IT experience. The wires for the antenna you can usually find for that laptop pretty cheap. The front digitizer can be popped off. You can do so by taking a thin flathead screw driver and prying around the edges of the plastic bezel and the back LCD cover....
Chosen Solution I replaced my iphone 5 bettery and plugged it. It went on and show the apple logo, but then it suddenly turned off then show the logo again. It went over and over and over, so I tried to disconnect the battery(so it will turn off) and connect it again . So when I press the power button(it’s turned off at this state because I already disconnected the battery and connected it again) or home button it won’t do anything....
Chosen Solution Model # UN60JS8000 So the problem i am having is around 15-20 minutes after turning on the tv and watching a show, there is lines running down and side to side on the tv. It also gets warm on the top of the tv. It seems as when it gets warm it has the lines running down it. When I turn it off and later turn it back on when its cool it has no issue at all....
Chosen Solution Hi. after combing the diy sites, here is what I’ve come up with. I have Power board BN44-00912A AND MAIN BOARD BN94-12295K. When I unplug the main board from power board the Back lights WORK. There are 2 cables running from power board to main board. I replaced the mainboard but this didn’t fix anything (might be DOA but not sure) I have checked power on the power supply board but there is no pin that is clearly marked STANDBY to look for the 3....
Chosen Solution Hi, I have 2000 MBps external ssd drive Sandisk Extreme Pro SSD and Im using MacBook Pro 2021 with thunderbolt 4, but only can get 1000 MBps rate tested through Blackmagic. I tried to find an article with this issue but can’t find any. There has been quite a few reports of slower USB-C native external drive performance, but much better Thunderbolt3 performance! There is a sizable I/O difference between the two USB-C connections!...
Chosen Solution Here is the problem: If I leave the phone for a couple of minutes with locked screen and then unlock it the screen brightness is normal but if I do something on it the after 2-3 minutes the screen goes very dark. Also the auto brightness is not working. What can be the problem? Maybe temperature sensor or proximity? Update (05/14/2016) The CPU is getting extremely hot and the screen starts dimming....
Chosen Solution I just changed over to a new screen and nothing is coming on what should i do. Sounds like you have blown the backlight. Can you confirm that you disconnected the battey when fitting the screen? If it’s not backlight related you probably have a bad screen with no display. Also check the flex cables on the screen that theyhave tape over any of the solder joints as this can short the screen out....
Chosen Solution really need help for my samsung galaxy!! At first my screen used to get frozen so i used to do hard factory reset for it but still it used to persist often then once when i factory resetted my phone the touch screen started working perfectly fine!! but then the menu key & the back key stopped working! only the home key & other rest of the keys are working....
Chosen Solution I removed the capacitor on the 5v7 (i think that is what it’s called) line for the display, and it came right back on! But I have a question, do I need to put a new capacitor on there? Or will the phone be ok? The caps you removed are C4200 & C4201 on the PP5V7_LCM_AVDDH rail. Capacitors fundamentally do one thing, that is store a charge. They have some amazing properties, which means you can use them for different purposes....
Chosen Solution Hello, I just got off chat with Apple and they said my rear camera sensor is broken (which is why the rear camera displays a black screen and flash isn’t working). If I use the guide to replace the camera I found on iFixIt, will that also replace the sensor or is that a totally different part I can purchase and replace instead? Thanks! Use this guide for the replacement and order this part to fix your rear camera....
Chosen Solution After i replaced my broken digitizer only the home button works - the touchscreen does not. Does anyone have a clue what that could be? By changing the digitizer i cut through the old digitizer cable, not thinking about that there was still the battery connected - could that have caused the problem. If yes, how can i fix it? I would say it’s a faulty screen you have recived just make sure cables are connected properly and disconnect the battery before you disconnect cables...
Chosen Solution Ok I have a whirlpool wtf535smbm00 my issue is it doesn’t go under 50 degrees. I have cleaned the front coils, and I have cleaned the back pan and backside. I have in plugged it for 10 minutes and re plugged it . Still u can hear the compressor kick on for a few seconds then kick off. Not sure what It is any help would help. I do hear a clicking noise when the compressor clicks on and when the compressor kicks off....
Chosen Solution Simply put, as the title says. Have attempted: -Software reset(on phone) -Starting phone without any of the screws on the LCD plate. Most notable fault is the phone not rotating. Below are shots of the app I use to check sensor data. To the left phone are the correct values: Proximity and light sensor fully functional. No water damage shown on indicators. For the fun of it, I downloaded the app on my phone to compare results....
